Material Sources Database

Laser Cutter

• Full Spectrum Laser SN 07/11/8350-639

Airfilter

• BOFA International Ltd: http://www.bofaamericas.com / 618-205-5007
• Filter # A1030055 + Prefilter # A1030056

Kapton Film

Used for solder stencils, sort of not as good as paper.

• Vendor: Kapton Source http://Kaptonsource.com/ (This vendor has died.)
  • 3 Mil by 12” by 36 yard roll
  • PC533FILM-12000-36
  • $315.00 + shipping

Bamboo

• Vendor: Revolution Bamboo http://bamboorevolution.com/
  • 1300 SE Grand Ave, Portland, OR, (503) 914-6262
• Order full sheets of 4’ x 8’ cut to a 4x6 array of around 12 x 16 inches
• 1/8 inch
• 1/4 inch

Acrylic

Port Plastics (our preferred source)

• Contact
  • Jim at 503-684-9335
  • 7500 SW Tech Center Drive #100, Portland, OR 97223
• Quote (9/5/12)
  • 1 full 4’ x 8’ sheet cut to a 4x6 array of 12 x 16 inches
  • 1/8” $2.80 / piece (3 mm?)
  • 3/16” $4.32 / piece
  • 1/4” $6.32 / piece
  • 3/8” $9.04 / piece (have a free supply, pretty thick, don’t really need)
  • 1/2” $13.52 / piece (Pretty thick, don’t really need)

Multicraft

• 503-352-0970
• 7298 SW Tech Center Drive, Tigard, OR 97223-8046

Laird

• Manager: Lee Ramsby
• 503-233-4861
• 2718 SE Raymond St, Portland, OR 97202

Tap Plastics

• Portland
  • 503-230-0770
  • 2842 NE Sandy Blvd, Portland, OR 97232
• Tigard
  • 503-620-4960
  • 15230 SW Sequoia Pkwy, Tigard, OR 97224

Gravoply Laser

• This is layered plastic that’s good for name plates (black covering white plastic)
• http://www.gravostore.com/
• Approx $12 for a 12” x 24” sheet
• Minimum orders required, about $35

3D Printer

We order everything directly from Mojo at http://shop.stratasys.com/

• Modeling material: “P430 Model Print Engine (ivory color in ABSplus)” # 350-80100, $399 for 80 cubic inches (1,311 cc)
• Support material: SR-30 Soluble Support Print Engine # 350-80200, $399 for 80 cubic inches (1,311 cc)
• Printing plates: “Modeling Bases” # 350-10000, $70 for 24 bases from
• Cleaning Tablets: Ecoworks Tablets #300-00104, $110 for 24 tablets

We can also recycle packs for free: https://www.stratasys.com/recycling/recycling-instructions

PCB Router

PCB stock (“bare boards”)

• EBay
  • PCB Depot
  • Unlike other PCB stock stores on EBay, these guys have a pull-down selection for different options, rather than having to wade through multiple listings.
  • Good prices
  • Standard or custom sizes
  • Mostly 1-oz double sided and 1 or 2-oz single-sided
  • Thicknesses from 0.005” to 0.062”
  • Recommendation for ordering:
    • 1/1 Double sided 1/16” (0.062”), 3 pieces, 9x12”: $14
    • Shipping: $11.95 Standard shipping; + $4 for each additional lot
    • As of 8/7/13 this listing has expired. - AM
• Think & Tinker LTD
  • 1/2 oz or 1 oz Double Sided 1/16” (0.062”), 5 pieces, 9x12”: $59.37
• Electronix Express
  • 1 oz Double Sided 1/16” (0.062”), $7.70/ea. when 10+ are ordered.
  • Most IEEE store parts are ordered from here so shipping is negligible.

LPKF S63

• Think & Tinker LTD
  • V-tip bits
    • LPKF 0.2mm Universal Mill replacement: EM2E8-0625-90V: 90deg 0.005” tip ($10.84)
• LPKF
  • V-tip bits
    • LPKF 0.2mm Universal Mill: ($180/10)

Laser Printer

HP LaserJet CM1415fnw

• Cyan toner cartridge: CE321A
• Magenta toner cartridge: CE323A
• Yellow toner cartridge: CE322A
• Black toner cartridge: CE320A

Soldering Station

• Thin solder wick: ITW Chemtronics 10ft of SOLDER-WICK NO-CLEAN .030” # 60-1-10 (DK 60-1-10-ND)
• Wide solder wick: ITW Chemtronics 10ft of SOLDER-WICK NO-CLEAN .110” # 60-4-10 (DK 60-4-10-ND)
• Flux pen: Kester Solder Formula 951 No Clean # 83-1000-0951 (DK KE1804-ND)
• Aggressive flux pen: MG Chemicals PEN RA ROSIN FLUX .34OZ W/TIP 835-P (DK 473-1033-ND)
• Solder: Kester SOLDER NO-CLEAN 28AWG 63/37 1LB #24-6337-8806 (DK KE1405-ND)